Google Temukan saya di Google+ Cara Detail Merakit Komputer: 3 TRICK HOW TO CORRECT FLASHDISK 0 Byte

Tuesday, April 1, 2014

3 TRICK HOW TO CORRECT FLASHDISK 0 Byte

---------------->   MOST IMPACT   <------------------
3 TRICK HOW TO CORRECT FLASHDISK 0 Byte

3 Easy Ways to Fix Damaged stick

Have you experienced when plugging in a flash, the flash is not readable at all alias is not detected by your operating system? Or even if detected by windows but after the properties had shown the capacity of 0 bytes when measuring 4 GB flash you? Well did you know that there is How to Fix the Damage stick and Troubled?

In this case we will describe a case of the brand Transcend flash detected by windows but read only 0 bytes in and out the window warning "Please insert a disk into drive H:" ie in this case the flash drive is detected in the drive H.

Well There are several alternative ways to resolve your flash issues. follow the following steps as How to Fix Damaged flash and the Problem:

Alternative Method 1: Utilize facilities HP USB Disk Storage Format Tool Format

You could try using software tools to format HP USB Disk Storage Format Tool. Software HP USB Disk Storage Format Tool is you can download for free over the internet. Although the production is destined flash HP, this tool can be very helpful to you. But if you still can not solve this problem, an alternative way you can do next.

Alternative Method 2: Using Software to fix the flash.

The second alternative is to utilize some of the tools or software that can be used to overcome the problems of damaged flash. You can download the software or the following tools:

Super Stick Recovery Tools
Low Level Format
Seatools for Windows

If the software or tools above still can not fix you. You should not despair, there is one that transcends the flash is detected with 0 kb's capacity. Let us refer to the way our last.

Alternative ways 3: Perform re reprogram the flash controller ICs

Well this is the way to do low level format a USB stick or flash the same time doing the program to re-flash controller IC. However, you must do the demolition casing flash to see the type of IC controler of your flash. In this case the controller is eg IC-AU6986 ALCOR. Then look at the google software tools to reprogram the IC as AlcorMP_UFD software for IC-AU6986 ALCOR.

Well this is the step by step that you have to do to use this tool AlcorMP_UFD program to fix our troubled flash (make sure you have downloaded the program AlcorMP_UFD for IC-AU6986 ALCOR here or here. Approximately 3,536 File size KB.

Extract the files that we downloaded earlier.
Live the ALCORMP.EXE file by double clicking.
Choose the setup menu, when out of the window just click OK password,
Replace Scan Mode into the Low Level Format.
Then click Start (A) to start the process, and wait until the process is complete.
After successfully re-format the stick once again you use the default Windows format facility.
Well, the flash is ready to serve again hehe


Warning: you are not allowed to register the 2x to check your incoming email after you finish registering. and click the link that goes to your inbox. thank you good luck on your download

before you download there as you join and login in order to succeed here to download
HP USB Disk Storage Format Tool Portable

Many are a bit confused when we overwrite Problem of flash 0 Byte broken with notification. In fact many are pessimistic about the broken stick can be used again. To fix the flash read 0 bytes, there are many alternative ways to use the software to fix, one of which is by using the program HP USB Disk Storage Format Tool.




Basically, HP USB Disk Storage Format Tool is a tool to format the flash, so that we can use this tool to format the flash that also can not be formatted with the default Windows format tool.  
Here's how to fix the flash 0 bytes by using this program.
  • Download HP USB Disk Storage Format Tool here  
  • Extract and install the program HP USB Disk Storage Format Tool that.
  • Insert the stick into the USB port of a computer
  • Run the application HP USB Disk Storage Format Tool
  • Determine where the flash drive is read 0 byte is attached
  • Select the desired file system, generally stick is formatted with the FAT32 file system
  •  
  • Click Start to begin formatting the flash.
  • When the alert window appears, click Yes.    
By using the program HP USB Disk Storage Format Tool, the broken stick problem which always read 0 bytes and can not be formatted can be reused.   

Please try good luck 

sources of : teknologi.wp-content/uploads/2013/10



If you are having trouble finding the file you are looking after your diuangdownload.com list can be downloaded here, the main thing is you have to be successful in the registration.
please download here

HP USB Disk Storage Format Tool disini

Read more at http://www.teknologi.co/27367/cara-memperbaiki-flashdisk-rusak-0-byte/
HP USB Disk Storage Format Tool disini

Read more at http://www.teknologi.co/27367/cara-memperbaiki-flashdisk-rusak-0-byte/

if unsuccessful use AlcorMP080424_AlcorMP_AU698X download here
if not contact my email. I am ready to help you : Nurmianis@gmail.com 

quoted from :
https://www.facebook.com/BandungComputerHomeService/posts/620568067961199  

No comments:

Post a Comment